
Mouse bites on a panel look like two rows of small holes. What actually sets the finished edge is the position of those hole rows relative to the final outline. Place the holes too far outward, and depaneling leaves a visible protrusion. Place them too far inward, and the break can cut into the finished edge. The design is complete only when the connecting tabs still survive reflow, handling, and placement, then break at the intended line. Copying hole diameter and pitch from an old board often copies appearance only, not the mechanical conditions.
Mouse Bites Define the Fracture Line
The router first cuts most of the outline and leaves connecting tabs at a few locations. The hole row then reduces the remaining cross-section of each tab so that, under hand or fixture depaneling, the crack prefers that line. Denser holes and narrower tabs usually lower break-out force, but they also lower panel stiffness. Required strength depends on board size, copper distribution, component mass, and tab orientation. When a connector, shield, or large inductor sits near the edge, the bend at the instant of break travels first into the solder joints.

Where the Hole Row Sits Matters More Than How Many Holes You Drill
Define the finished outline first, then decide whether the hole centerline offsets inward or outward. If residual material must not extend beyond the outline, the holes are often allowed to enter the board slightly. That inward offset must not consume mechanical dimensions, copper-to-edge clearance, or component courtyards. If a housing slot needs a flat edge, mouse bites may be allowed only in an area that can be dressed, or the design should switch to routed slots and fixture depaneling. A "negative tolerance" is not an excuse to push holes inward at will. It means quantifying both allowed leftover material and allowed notches at the same time.

Place Tabs Around How the Panel Is Loaded
A small board held by tabs on only one side can swing like a cantilever during reflow transport, pickup, or handling. Tabs crowded into the corners can let the mid-span of a long edge sag. A more stable approach is to spread tabs around the outline according to board shape, and to keep them away from precision connectors, weak cutouts, and stress-sensitive parts. Tab width and tab count belong together: more tabs improve handling stability and also add more break points and more residual-edge work. Large panels also need to account for tooling strips, tooling holes, and warpage from component mass.

Keep Copper, Solder Mask, and Parts Off the Crack Path
The fracture does not stop exactly at the hole circle. Traces, copper pours, vias, ceramic capacitors, and BGA joints near the edge need clearance. The exact value comes from fabricator capability and the product's mechanical requirements. Copper that crosses a tab raises break-out force and can tear into burrs. Solder mask and silkscreen sitting on the fracture zone make the finished appearance hard to control. If parts must sit on a narrow edge, move the tabs or use a depaneling fixture. Do not release the layout only because nothing appears to touch a hole in the drawing.

Review the Mechanical Layers Before Release
The fabrication package should let the board house identify the finished outline, slot centerlines, mouse-bite diameter, whether the holes are plated, tab width, and allowed residual edge. Do not write "process as mouse bites" in a note while the mechanical layers contain overlapping lines, broken outlines, or several conflicting contours.
At panel review, also check whether tabs block test points or pickup nozzles, whether edge parts will be hit by the depaneling fixture, and whether the break direction will bend brittle components. First articles should keep after-break edge photos and measured dimensions, then use those results to calibrate hole-row offset on later similar boards instead of locking one set of experience numbers forever.
Inspection after depaneling cannot stop at front-side burrs. Use a loupe or microscope along both sides of each tab to see the glass-fiber tear direction, then measure the largest protrusion and the largest notch. Edge MLCC parts, crystals, and connector joints may need a visual recheck or electrical sampling. If hand break-out requires an obvious twist, stress is already entering the board surface. Do not solve that by asking the operator to "use less force." Redistribute the stress through tab width, tab location, hole-row position, and the depaneling method. When a housing has locating ribs or a sealing face, put the residual-edge measurement datum on the mechanical drawing so design, fabrication, and assembly do not each interpret a different edge.
The value of mouse bites is not that the board "can be snapped." It is that the panel stays stable through manufacturing, breaks at a defined location, and keeps residual material and stress inside what the product allows. Hole diameter and pitch are variables. Finished outline, edge clearance, tab loading, and depaneling method are the inputs. If a first-article edge shows a crack running inward, stop reusing the old numbers and reset tab locations from the mechanical constraints.
Boards that must fit a housing, a seal, or a guide rail should list maximum protrusion and maximum notch as separate mechanical acceptance limits. If a tab sits near a ceramic capacitor, crystal, or edge connector, first-article checks should add a magnified local inspection and compare crack direction under different break orientations. Design, fabrication, and assembly must share one finished-edge datum, or each step can pass and the board still will not fit the structure. Write the review result back onto the next panel drawing. Do not leave it only in shop-floor photos.