Coupons
Help
  • FAQ
    browse most common questions
  • Live Chat
    talk with our online service
  • Email
    contact your dedicated sales:

PCB Layout and Routing Rules: Vias, Stubs, Loop Area, and EMC Terms

Author : Alex Chen | PCB Design & High-Speed Engineering Specialist

November 20, 2026



PCB layout and routing determine whether a design meets its signal-integrity, power-integrity, and electromagnetic-compatibility targets. At high speed, routing is not just a connection problem: every via, corner, stub, and return path becomes a parasitic element that can reflect energy, couple noise, or radiate. The routing rules in this article address those failure mechanisms directly, from via inductance and right-angle field concentration to plane integrity, loop-area control, and EMC terminology. The examples from appliance PCBs show that the same principles apply beyond high-speed digital boards.

Highlights:

  • Keep high-speed signal vias to an absolute minimum. A via adds roughly 1 to 4 nH of inductance and 0.3 to 0.8 pF of capacitance to the path; when layer changes are unavoidable on parallel buses, match the via count on every signal line.
  • Avoid right-angle corners, stubs, star routing, and radial routing on high-speed or sensitive nets. Use 45-degree turns, constant trace width, and tight signal-return coupling to control reflections, radiation, and loop area.
  • Treat power and ground planes as part of the routing. Via clusters and split apertures create local impedance discontinuities, while ungrounded metalized features and large signal-return loops can act as antennas.

 

Layout and Routing Techniques

The following sections discuss several PCB routing rules.

Vias

Vias are commonly used in multilayer printed circuit boards. When a high-speed signal passes through a via, the via introduces 1 to 4 nH of inductance and 0.3 to 0.8 pF of capacitance into the path. Therefore, when routing high-speed signal channels, vias should be kept to an absolute minimum. For high-speed parallel lines, such as address and data lines, if a layer change is unavoidable, make sure that every signal line has the same number of vias.

45-Degree Routing

Like vias, right-angle path turns should be avoided because they can concentrate the electric field at the inner edge. That field can couple noise into adjacent paths. Therefore, when a route must turn, all right-angle turns should be replaced with 45-degree turns. Figure 25 shows the general rule for angled routing.

Figure 25 | Angled path

Figure 25 | Angled path

Stubs

A stub produces reflections and can also act as a wavelength-dependent antenna that couples into the circuit. Even if the stub length is not an integer quarter-wavelength of any known signal in the system, the associated radiation can still resonate on the stub. Therefore, avoid stubs on high-frequency and sensitive signal paths.

Figure 26 | Stub

Figure 26 | Stub

Star Signal Arrangement

Although a star arrangement is suitable for ground connections from multiple PCBs, it creates signal paths with multiple stubs. Therefore, star arrangements should be avoided for high-speed and sensitive signals.

Radial Signal Arrangement

Radial signal routing usually provides the shortest path and the minimum delay from source to receiver, but it can also produce multiple reflections and radiated interference. Therefore, radial arrangements should be avoided for high-speed and sensitive signals.

 

Part 3: PCB Routing Techniques

Constant Trace Width

The width of a signal path should be constant from driver to load. Changing trace width changes the path impedance, including resistance, inductance, and capacitance, which can produce reflections and create an impedance imbalance. It is best to keep the trace width unchanged.

Via and Hole Density

A dense cluster of vias passing through power and ground planes creates a localized impedance difference near the vias. This region not only becomes a "hot spot" of signal activity; the power plane is also high-impedance at that point and is inefficient for RF current.

Split Apertures

As with dense holes and vias, split apertures, meaning long slots or wide channels, create inconsistent regions in power and ground planes. They reduce the effectiveness of those planes as shields and locally increase the impedance of the power and ground planes.

Grounded Metalized Features

All metalized features should be connected to ground. Otherwise, these large metal areas can act as radiating antennas.

Minimizing Loop Area

Keeping the signal path and its ground return close together helps minimize the ground loop and avoids a potential antenna loop. For high-speed single-ended signals, if the signal path does not run along a low-impedance ground plane, a ground trace may also need to follow the signal path (Figure 27).

Figure 27 | Ground loop

Figure 27 | Ground loop

PCB Example 1

Figure 28 illustrates several improvements to a typical washing machine PCB.

Figure 28 | PCB improvement example 1

Figure 28 | PCB improvement example 1

PCB Example 2

Figure 29 illustrates several improvements to a typical air-conditioner PCB.

Figure 29 | PCB improvement  Example 2 Appendix A: Glossary

Figure 29 | PCB improvement – Example 2 Appendix A: Glossary

These appliance examples show that the same routing rules apply beyond high-speed digital boards. Return-path continuity, loop area, and plane integrity still determine whether the board radiates or is susceptible to interference.

 

Appendix A: Glossary

Electromagnetic Compatibility (EMC)

Electromagnetic compatibility is the ability of an electrical or electronic system, device, or equipment to operate within a specified electromagnetic environment without causing an unacceptable degradation in design level or performance due to electromagnetic interference (ANSI C64.14-1992).

Electromagnetic Interference (EMI)

A lack of electromagnetic compatibility is fundamentally a lack of compatibility. Electromagnetic interference is the process by which fragmented electromagnetic energy is transferred from one electronic device to another through radiated or conducted paths, or both. The term usually refers specifically to RF signals. EMI can occur over the frequency range from DC to daylight.

Radiated Emissions

Radiated emissions are the component of RF energy transmitted through a medium as an electromagnetic field. RF energy usually travels through free space; however, other field propagation modes can also occur.

Conducted Emissions

Conducted emissions are the component of RF energy transmitted through a medium as a guided wave, generally along wires or interconnect cables.

Immunity

Immunity is a relative measure of the ability of a device or system to withstand electromagnetic interference while maintaining a predetermined performance level.

Electrostatic Discharge (ESD)

Electrostatic discharge is the transfer of charge that occurs when two objects at different potentials approach each other or make direct contact. The observed phenomenon is a high-voltage pulse, and that pulse can damage or disable sensitive devices. Although lightning differs in magnitude from these pulses, the term electrostatic discharge is usually applied to lower-amperage events, especially those initiated by humans.

Radiated Immunity

Radiated immunity is the relative ability of a product to resist electromagnetic energy propagating from free space.

Conducted Immunity

Conducted immunity is the relative ability of a product to resist electromagnetic energy that penetrates through external cables, wires, and input/output interconnections. If the connection is incorrect, EMI can increase.

Susceptibility

Susceptibility is the tendency of an electronic device or system to be disturbed, damaged, or affected by electromagnetic interference from nearby electromagnetic fields or signals. It is the lack of immunity.

Related Reading:

Alex Chen | PCB Design & High-Speed Engineering Specialist Alex Chen | PCB Design & High-Speed Engineering Specialist

Alex Chen is a senior PCB design engineer with extensive experience in high-speed and high-density circuit design. He specializes in signal integrity, impedance control, and multilayer PCB layout optimization. At AIVON, he reviews and refines content related to PCB design principles, EDA tools, and advanced layout techniques. His expertise helps engineers avoid common design pitfalls and improve performance, reliability, and manufacturability in complex PCB projects.

Related Tags


2026 AIVON.COM All Rights Reserved
Intellectual Property Rights | Terms of Service | Privacy Policy | Refund Policy