Coupons
Help
  • FAQ
    browse most common questions
  • Live Chat
    talk with our online service
  • Email
    contact your dedicated sales:

Improving PCB Immunity to Power Supply Variations in Converter Systems

Author : Alex Chen | PCB Design & High-Speed Engineering Specialist

November 17, 2026


Power-supply noise is a persistent risk in mixed-signal PCB design. For an ADC or another high-speed converter, noise on any supply input can couple into the signal chain and reduce effective performance. The converter alone does not determine immunity. Regulator selection, power-supply rejection ratio (PSRR), converter noise floor, filtering, grounding, and layout all interact. This article explains how to evaluate supply noise against converter noise limits, when regulator noise actually matters, and which board-level practices improve immunity to supply variations.

Highlights:

  • Regulator noise must be evaluated together with converter PSRR and converter noise floor. With 60 dB PSRR, even a relatively noisy switching regulator can contribute far less noise than the ADC noise floor.
  • Decoupling, filtering, grounding, and circuit partitioning are part of the noise budget, not afterthoughts. Tightly spaced power and ground planes and controlled return paths improve high-frequency immunity.
  • Multi-channel systems change the analysis. Doubling the number of uncorrelated ADC channels lowers the system noise floor by 3 dB, which makes supply design constraints tighter as channel count rises.

 

Maximizing PCB Immunity to Power-Supply Variations

For a converter and for the end system, the design must ensure that noise on any given input does not affect performance. To understand supply noise and meet system requirements, the evaluation should follow a defined sequence: first select the converter, then select the regulator, LDO, switching regulator, or other power source, and then verify whether the combined noise performance is acceptable.

  1. Select the converter first, then select the regulator, LDO, switching regulator, or other power source. Not every regulator is suitable. Review the regulator datasheet for noise and ripple specifications, and for switching frequency if a switching regulator is used. A typical regulator may have 10 μV rms noise over a 100 kHz bandwidth. Assuming this noise is white noise, it corresponds to a noise density of 31.6 nV rms/√Hz in the target frequency band.
  2. Check the converter's power-supply rejection ratio to understand when converter performance will degrade because of supply noise. In the first Nyquist zone, fS/2, the PSRR of most high-speed converters is typically 60 dB (1 mV/V). This value defines how much supply noise is attenuated before it reaches the converter.
  3. Consider a 16-bit ADC with a 2 V p-p full-scale input range, 78 dB SNR, and a 125 MSPS sampling rate. Its noise floor is 11.26 nV rms. Noise from any source must remain below this value to avoid affecting the converter. In the first Nyquist zone, the converter noise is 89.02 μV rms (11.26 nV rms/√Hz) × √(125 MHz/2). Although the regulator noise (31.6 nV/√Hz) is more than twice the converter noise, the converter has 60 dB PSRR, which suppresses the switching-regulator noise to 31.6 pV/√Hz (31.6 nV/√Hz × 1 mV/V). This noise is much smaller than the converter noise floor, so the regulator noise will not degrade converter performance.
  4. Power filtering, grounding, and layout are equally important. Adding a 0.1 μF capacitor at the ADC supply pin can reduce noise below the value calculated above. Keep in mind that some supply pins draw more current or are more sensitive than other supply pins. Decoupling capacitors should therefore be used carefully, and some supply pins may require additional decoupling. A simple LC filter at the power-supply output also helps reduce noise. When a switching regulator is used, cascaded filters can suppress noise to a lower level. Remember that each additional stage in the cascade contributes approximately 20 dB per decade.
  5. The analysis above applies to a single converter. If the system includes multiple converters or channels, the noise analysis changes. For example, an ultrasound system uses many ADC channels that are summed digitally to improve dynamic range. In basic terms, each doubling of the channel count reduces the converter or system noise floor by 3 dB. In the example above, using two converters halves the converter noise floor (-3 dB); using four converters gives -6 dB. The reason is that each converter can be treated as an uncorrelated noise source. Uncorrelated noise sources are independent of one another, so they can be combined using an RSS (root sum square) calculation. Ultimately, as the channel count increases, the system noise floor decreases, the system becomes more sensitive, and the supply design constraints become stricter.

It is impossible to eliminate all power-supply noise from an application, because no system is completely immune to supply noise. As an ADC user, the practical approach is to address the issue proactively during the power-supply design and layout stages.switching power supply layout

Practical Guidelines for Supply Decoupling and Layout

The following practices help maximize PCB immunity to power-supply variations:

  • Decouple all power rails and bus voltages that reach the system board.
  • Remember that each additional stage contributes approximately 20 dB per decade.
  • If the supply leads are long and feed a specific IC, device, or area, decouple again at that point.
  • Decouple both high and low frequencies.
  • Use a series ferrite bead at the power entry point before the decoupling capacitor ground. Apply this to every supply voltage entering the system board, whether it comes from an LDO or from a switching regulator.
  • For the capacitors that are added, use tightly stacked power and ground planes with spacing ≤4 mil so that the PCB design itself provides high-frequency decoupling capability.
  • As with any good board layout, keep power supplies away from sensitive analog circuits, such as the ADC front-end stage and clock circuits.
  • Good circuit partitioning is critical. Some components can be placed on the back side of the PCB to improve isolation.
  • Pay attention to ground return paths, especially on the digital side, and ensure that digital transients do not return into the analog portion of the board. In some cases, split ground planes may also be useful.
  • Keep analog and digital reference components on their respective layers. This common practice improves isolation from noise and coupling interactions.
  • Follow the IC manufacturer's recommendations. If the application note or datasheet does not state the information directly, study the evaluation board. These are very good starting tools.

Supply Decoupling and Layout

Related Reading:

Eight Layout Considerations for Differential Filters on PCBs

PCB Layout for Accurate Temperature Measurement: PCB vs Ambient

Best Grounding Practices for Data Converters: Return Paths and Error Voltage

High-Temperature IC Packaging: Die Attach, Wire Bond, Solder and PCB

isoPower Radiated Emissions: Dense PCB Layout Guide

Buck Regulator PCB Layout and Grounding Guide for Low Noise

PCB Thermal Design: Junction Temperature and Power Dissipation

LFCSP Package Rework: Safe Removal and Replacement on PCBs

PBGA Rework Procedure: Removal, Pad Cleaning, Paste and Placement

Alex Chen | PCB Design & High-Speed Engineering Specialist Alex Chen | PCB Design & High-Speed Engineering Specialist

Alex Chen is a senior PCB design engineer with extensive experience in high-speed and high-density circuit design. He specializes in signal integrity, impedance control, and multilayer PCB layout optimization. At AIVON, he reviews and refines content related to PCB design principles, EDA tools, and advanced layout techniques. His expertise helps engineers avoid common design pitfalls and improve performance, reliability, and manufacturability in complex PCB projects.

Related Tags


2026 AIVON.COM All Rights Reserved
Intellectual Property Rights | Terms of Service | Privacy Policy | Refund Policy