Integrated isolated power devices such as isoPower combine an isolated DC-DC converter with iCoupler digital isolation in a single package. The converter switches relatively large currents at frequencies from 125 MHz to 200 MHz. At these frequencies, PCB traces, vias, reference planes, and return paths behave as unintended antennas, so both radiated emissions and conducted noise become important design concerns. When several isoPower devices are placed close together on a dense board, the interaction between their switching stages, isolation barriers, and shared reference planes makes emission control more difficult. This article explains how circuit optimization, multilayer stackup design, interlayer stitching capacitance, isolation spacing, and cable filtering can be combined to suppress emissions without compromising the isolation barrier.
Highlights:
- isoPower converters switch large currents at 125 MHz to 200 MHz, so the layout must control high-frequency current loops and radiated fields.
- Circuit optimization combined with stitching capacitance across the isolation barrier can reduce peak emissions by more than 25 dB.
- In dense multi-device layouts, use as many PCB layers as practical, overlap reference planes across barriers and adjacent channels, preserve clearance and creepage, and filter cable connections.
Why Dense isoPower Layouts Need Emission Control
The emission challenge begins with the isolated DC-DC converter inside each isoPower device. Its switching current flows through the package, the power and ground planes, and the isolation barrier. At high frequency, even short PCB features can carry significant current, and the resulting loops can radiate. Voltage differences across the isolation barrier can also drive common-mode current onto cables and other board structures. The layout must therefore control both the local current loop of each converter and the larger current paths that can form when several converters share a board.
With a single device, established circuit and layout measures can be effective. With multiple devices in a dense layout, those measures must be applied consistently across all channels, and the stackup must provide enough low-inductance return paths to keep high-frequency current close to its source.
Start with Circuit-Level Emission Reduction
Circuit optimization should be addressed before layout because it reduces the strength of the emission source. Lowering the load current and supply voltage reduces the current that the converter must switch. The second measure is to provide stitching capacitance across the isolation barrier using PCB inner-layer capacitance. This capacitance creates a low-inductance path for high-frequency current that would otherwise drive the barrier and nearby planes.
When circuit optimization and stitching capacitance are used together, peak emissions can be reduced by more than 25 dB. That reduction is significant because it changes the layout problem from containing a strong radiator to managing a source that has already been reduced. However, the same measures must still be planned carefully when several isoPower devices are placed close together and the available board area is limited.
Build Low-Inductance Stitching Capacitance in the PCB Stackup
The most effective stitching capacitance is built inside the PCB rather than added as a narrow trace or a remote component. Internal planes form a low-inductance structure because the copper overlap is wide and the dielectric separation is small. When the overall PCB area is constrained, a multilayer board is a practical way to obtain that structure. Use as many layers as are practical, and overlap power and ground planes, which serve as reference layers, over as much area as possible. The stackup example below illustrates the principle.
Buried layers on the primary and secondary sides can carry power and ground currents. An overlap that crosses the isolation barrier, such as primary-side ground and secondary-side VISO, creates effective stitching capacitance. Several such overlaps in a multilayer stack add capacitance in parallel. To maximize capacitance, reduce the thickness of the PCB dielectric between reference layers. The stackup must still satisfy the isolation voltage, spacing, and manufacturability requirements of the final application.
The quality of the stitching capacitor depends on inductance as well as capacitance. A capacitor formed by wide internal planes has much lower inductance than a narrow trace or a component placed at the board edge. The stackup should therefore be planned so that power and ground currents on both sides of the barrier have continuous reference planes and the copper overlap is close to the barrier where the high-frequency current needs to return. A thin dielectric increases capacitance for a given overlap area, but it must not compromise isolation or manufacturing requirements.
Overlap Adjacent isoPower Channels
A second layout technique is to overlap the layers associated with adjacent isoPower channels. The example below shows multiple adjacent channels.

Four adjacent channels with overlapping stitching capacitors
Each output domain remains isolated from every other domain, but the physical overlap between neighboring domains can still contribute useful capacitance. The stackup detail below shows how each isoPower device can add capacitance and how the overlapping structure can extend across adjacent isolation regions.
This approach is useful when board area is tight and a single large stitching capacitor is not possible. The overlap uses copper that is already needed for power and ground distribution, so it can add capacitance without requiring a discrete capacitor across the barrier. It does not replace the need for stitching capacitance across each individual isolation barrier, but it uses the available copper more efficiently and helps control high-frequency current that would otherwise spread across the board.
Maintain Isolation Spacing and Filter Cable Connections
The internal and external gap requirements must be checked against the final application. Any copper overlap used for stitching capacitance must not reduce the required clearance or creepage at the isolation barrier. This is a layout constraint, not an optional check. A board may have excellent emission performance but still be unacceptable if the isolation spacing is insufficient. It is therefore useful to define the isolation barrier and the required spacing first, then design the copper overlap inside the allowed area.
Ferrite beads can also be used on any cable connection to provide filtering and reduce the antenna effect that can make a cable radiate. A cable connected to the board can carry high-frequency current away from the PCB and act as an efficient radiator because it is long compared with the PCB features. A ferrite bead presents high impedance at the relevant frequencies and helps limit that current. Filtering should be provided on any cable connection that can produce this effect.
Design Checklist for Multiple isoPower Devices
For a dense board with multiple isoPower devices, the main recommendations can be summarized as follows:
- Minimize the power requirement of each channel.
- Build stitching capacitance across multiple PCB layers.
- Use as many PCB layers as practical.
- Use the thinnest dielectric available between reference layers.
- Provide connection and overlap between adjacent domains.
- Confirm that internal and external creepage distances still meet requirements.
- Provide filtering on cable connections.
These measures are complementary. Reducing the source current lowers the emission level, multilayer stitching and plane overlap reduce the high-frequency loop area, adjacent-domain overlap uses the available copper, clearance checks preserve the isolation barrier, and cable filtering addresses radiation from attached wiring. In a dense board with multiple isoPower devices, the layout should be evaluated as a complete system rather than as a set of isolated components.
Related Reading:
Eight Layout Considerations for Differential Filters on PCBs
Improving PCB Immunity to Power Supply Variations in Converter Systems
PCB Layout for Accurate Temperature Measurement: PCB vs Ambient
Best Grounding Practices for Data Converters: Return Paths and Error Voltage
High-Temperature IC Packaging: Die Attach, Wire Bond, Solder and PCB
Buck Regulator PCB Layout and Grounding Guide for Low Noise
PCB Thermal Design: Junction Temperature and Power Dissipation
LFCSP Package Rework: Safe Removal and Replacement on PCBs
PBGA Rework Procedure: Removal, Pad Cleaning, Paste and Placement