Encapsulating a die and attaching it to a PCB for operation at elevated temperature is far from a straightforward task. At high temperature, a long list of mechanical, metallurgical, and material factors can each erode package integrity (Figure 1). Sourcing silicon that functions at high temperature solves only half of the problem: every material in the assembly, every interface between those materials, and every process used to join them must survive the same thermal envelope for the entire service life of the product.
This article walks through the packaging chain one element at a time: die attach, wire bonding, the package body, lead configuration and metallization, solder alloy selection, and the PCB laminate itself. For each element it identifies the failure mechanisms that dominate at elevated temperature, the material choices that mitigate them, and the way the resulting design is verified in the laboratory through high-temperature operating life testing and acceleration models.
Highlights:
- Die attach materials must remain functional above their glass transition temperature, and the coefficient of thermal expansion (CTE) of die, attach material, and substrate must be matched so that repeated thermal cycling does not shift electrical parameters.
- Gold wire bonded to aluminum pad metallization is the classic high-temperature failure case: intermetallic compound growth embrittles the joint while Kirkendall diffusion opens voids that reduce strength and raise resistance, which is why monometallic bonds or slow-diffusing metal pairs are preferred.
- Plastic packages are rated for continuous use at 150°C, extendable to 175°C only for short periods, so hermetic ceramic packages are the safer choice above that point, at the cost of size, weight, and price.
Die Attach: Where CTE Matching Begins
The die attach material is what holds the silicon to the package or to the substrate. Many materials that are perfectly stable over a standard temperature range have a comparatively low glass transition temperature (Tg) and are therefore unsuitable for high-temperature service. Above Tg, key mechanical properties such as the expansion coefficient and the modulus change significantly, so a joint that behaves predictably at room temperature can begin to move, creep, or crack when the assembly is hot.
Matching the coefficient of thermal expansion of the die, the die attach material, and the substrate needs particular attention. If the three expand at different rates, the die is subjected to repeated mechanical stress across a wide temperature range and can eventually fracture. Even a small amount of mechanical stress on the die may be enough to shift electrical parameters to a level that precision applications cannot accept, which makes die attach a signal-chain concern as much as a mechanical one. For power devices that require both a thermal and an electrical connection to the package substrate, a metallic die attach material may be necessary to carry heat and current at the same time.
Wire Bonding: Intermetallic Growth and Kirkendall Voids
Wire bonding interconnects the die and the package pins by running a metal wire from the lead frame to the pads on the die surface. For bond reliability at high temperature, the compatibility of the wire metal with the pad metallization is the dominant concern.
Failures caused by poor metallurgical compatibility take two forms:
- Intermetallic compound (IMC) growth at the boundary interface, which makes the bond brittle;
- Diffusion (the Kirkendall effect), which generates voids at the interface, reducing bond strength and increasing its resistance.
Unfortunately, one of the most common metal combinations in the industry, gold wire on aluminum pad metallization, is precisely the combination that is prone to both phenomena at elevated temperature. Figure 1 shows a cross-section of a gold/aluminum bond in which IMC growth has developed after 500 hours at high temperature, to the point where bond integrity is affected.

Figure 1 | Gold/aluminum bond after 500 hours at 195°C
Figure 2 shows the same failure mode in more advanced form: pronounced gold/aluminum intermetallic growth together with Kirkendall voids after a high-temperature bond failure. The situation is made worse by halogens such as bromine and chlorine, which are sometimes present in molding compounds. At high temperature these elements cause corrosion at the boundary interface and accelerate bond failure. Fortunately, the industry has largely converted to "green" halogen-free molding compounds, which removes this particular contributor.

Figure 2 | Intermetallic compound growth producing voids
The practical conclusion is that the wire and the pad should ideally use the same metal, a monometallic bond, which eliminates the adverse effects described above. Where a monometallic bond is not possible, engineers should select a metal pair whose IMC growth and diffusion rates are slow enough that the bond remains reliable over the required service life.
Figure 3 illustrates how robust a monometallic bond is at high temperature. In the bond cross-section there is no sign of IMC growth after 3000 hours at 195°C.

Figure 3 | Monometallic bond after 3000 hours at 195°C
IC Packaging: Plastic Versus Hermetic Ceramic
The package body itself must withstand the stresses imposed by a harsh environment. Plastic packages, although they are the industry standard, have traditionally been rated for continuous use only at 150°C. As high-temperature applications have drawn more attention, studies have shown that this rating can be extended to 175°C, but only for short periods. Structurally, 175°C is the point at which some materials in the package, molding compound among them, exceed their glass transition temperature. Operating above Tg produces significant mechanical changes in key parameters such as CTE and flexural modulus, and the resulting thermal strain drives bond failures including delamination and cracking.
For high-temperature applications, a hermetic ceramic package is therefore the better choice (Figure 4). The hermetic seal prevents the ingress of moisture and contamination, both of which promote corrosion.

Figure 4 | Hermetically sealed side-brazed ceramic DIP package
The drawback is that hermetic packages are typically larger, heavier, and considerably more expensive than their plastic equivalents. In applications where the extreme-temperature requirement is less demanding (below 175°C), a plastic package is often the better trade: it reduces PCB area and cost, or it can provide better vibration compliance. For systems that need both a hermetic package and high device density, a high-temperature multichip module is a sensible solution, although it requires known good die to be available.
Package Lead Configuration and Metallization
Lead configuration and lead metallization must be evaluated with the same care. The quality of a surface-mount device depends only on the pad area and on the quality of the bond between the copper layer and the prepreg material. A through-hole DIP configuration, one of the most reliable packages available, additionally provides robust shock and vibration performance. In extreme cases, connection strength can be pushed further by bending the leads on the underside of the board and "staking" them to the PCB. Through-hole pinouts, however, prevent dense placement of components on the bottom side of the board, which can be a serious problem in applications with tight space constraints, such as downhole instruments.
In many cases a gull-wing SMT lead configuration is a workable alternative, but leadless SMT packages are not robust enough under the high shock and vibration found in many high-temperature environments. When SMT devices are used, designers should consider their height and mass. High-temperature epoxy can improve connection robustness, but it increases manufacturing cost and makes repair more difficult. In every case, the lead metallization must be compatible with the high-temperature solder being used.
Selecting a Solder Alloy for High-Temperature Assembly
The most common standard solder alloys melt below 200°C. A number of readily available alloys fall into the "high melting point" (HMP) category, with melting points well above 250°C. Even for these alloys, the maximum recommended operating temperature for any solder subjected to stress is roughly 40°C below its melting point. As an example, a standard HMP solder alloy consists of 5% tin, 93.5% lead, and 1.5% silver, with a melting point of 294°C, yet its recommended maximum operating temperature is only 255°C. It should also be noted that BGA packages carry factory-attached solder balls whose melting point may not be as high.
The PCB as a Failure Source
The PCB itself can be the source of a joint failure. Standard FR4 material can exhibit a glass transition anywhere between 130°C and 180°C, depending on its specific composition. Using the board above that temperature, even briefly, promotes diffusion and delamination. Polyimide, the material used in Kapton, is a dependable alternative with a Tg as high as 250°C, again depending on composition. Polyimide, however, is extremely hygroscopic, and absorbed moisture can make the PCB fail rapidly through a variety of mechanisms, so controlling its exposure to moisture is essential. In recent years the industry has introduced new laminate materials with lower moisture absorption that retain their integrity at high temperature.
Verifying High-Temperature Devices in the Laboratory
Do parts such as the AD8229 instrumentation amplifier, designed for high-temperature environments, actually resolve all of the issues described above? Answering that question means verifying, qualifying, and testing the device in the laboratory.
Validating a high-temperature device in the lab is not easy, because the engineer must combine all of the techniques above to measure device performance at extreme temperature. Beyond building the test fixture from special materials, the test engineer must operate the environmental chamber carefully so that the system is brought to the required temperature profile in a controlled way. Because of expansion coefficient mismatch, rapid temperature changes can damage solder joints on the PCB, cause warping, and ultimately make the system fail prematurely.
Accelerated Life Testing and the Arrhenius Model
To shorten the life and reliability test cycle, testing electronic devices at elevated temperature is an accepted approach. This introduces an acceleration factor, α, calculated from the Arrhenius equation:
α = exp[(Ea / k) × (1 / Ta ? 1 / Ts)]
where Ea is the activation energy, k is the Boltzmann constant, Ta is the expected operating temperature in use, and Ts is the stress temperature. Although accelerated aging is not a major issue for standard products, a stress temperature far above the rated temperature can trigger new failure mechanisms and produce inaccurate results.
To establish the lifetime reliability of a high-temperature device such as the AD8229, high-temperature operating life (HTOL) testing is therefore performed at the maximum rated temperature of 210°C for 1000 hours, roughly six weeks. For lower temperatures, the expected life can be predicted using the acceleration relationship shown in Figure 5.

Figure 5 | AD8229 lifetime vs. operating temperature, 1000 hours (210°C) 11
Test System Reliability and Statistical Confidence
Reliable characterization of high-temperature ICs faces other obstacles. A test and measurement system, for instance, is only as reliable as its weakest link: every element exposed to high temperature for a long period must itself be more reliable than the IC under test. An unreliable system produces data that says nothing about the long-term reliability of the device and forces the whole process to be repeated, which is both expensive and time-consuming. Statistical techniques can improve the success rate, including accurately sizing the test sample to add error margin and prevent premature system failures caused by DUT (device under test) failures. A further obstacle comes from the production steps required to guarantee performance parameters at extremes, such as test, probe, and trim.
Related Reading:
Eight Layout Considerations for Differential Filters on PCBs
Improving PCB Immunity to Power Supply Variations in Converter Systems
PCB Layout for Accurate Temperature Measurement: PCB vs Ambient
Best Grounding Practices for Data Converters: Return Paths and Error Voltage
isoPower Radiated Emissions: Dense PCB Layout Guide
Buck Regulator PCB Layout and Grounding Guide for Low Noise
PCB Thermal Design: Junction Temperature and Power Dissipation
LFCSP Package Rework: Safe Removal and Replacement on PCBs
PBGA Rework Procedure: Removal, Pad Cleaning, Paste and Placement