Reliable operation of high-power integrated circuits increasingly depends on effective thermal management. Every semiconductor has a specified maximum junction temperature, or TJ, and that limit is typically 150°C, sometimes 175°C. Like a maximum supply voltage, the maximum junction temperature is a worst-case constraint that must not be exceeded. Conservative designs leave adequate safety margin. This is critical because semiconductor lifetime is inversely related to operating junction temperature. In simple terms, the lower the IC temperature, the more likely the device is to reach its longest service life.
Highlights:
- Junction temperature is a worst-case reliability limit, commonly 150°C, with some devices specified to 175°C.
- The AD8017AR in an 8-pin SOIC package is rated at 1.3W at 25°C ambient only under specified PCB heat-spreading conditions, including a double-layer board with approximately 4 in2 (~2500 mm2) of 2 oz copper.
- The thermal path is described by θJA = θJC + θCA and TJ = TA + (P × θJA), which allow safe operating conditions to be predicted when board area, copper, airflow, or ambient temperature changes.
These power and temperature limits are important and appear in typical datasheets.
Junction Temperature Limits and Reliability
The maximum power that can be safely dissipated by the AD8017 is limited by the associated rise in junction temperature. The maximum safe junction temperature for a plastic encapsulated device is determined by the glass transition temperature of the plastic, approximately +150°C. Temporarily exceeding this limit may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of +175°C for an extended period can result in device failure.
The thermal rating is therefore not a single isolated number. It is tied to specific operating conditions, including device power dissipation and the mounting details of the package on the printed circuit board (PCB). The datasheet limit describes what the device can safely dissipate when those conditions are met, and the designer must account for the actual board and environment used in the application.
Power Dissipation Rating and PCB Thermal Conditions
For the AD8017AR, the rated power dissipation at 25°C ambient temperature is 1.3W. This rating assumes that the 8-pin SOIC package is used with a double-layer PCB that provides heat spreading through approximately 4 in2 (~2500 mm2) of 2 oz copper. Those PCB conditions are part of the power rating, not incidental details. If the copper area, copper weight, board construction, airflow, or ambient temperature differs, the safe power dissipation must be predicted for the new conditions.
This is why thermal design for high-power ICs cannot rely only on the headline wattage in a datasheet. The same package can dissipate much less power when mounted on a small copper area or in a closed enclosure with little airflow. Conversely, a larger copper area and better heat spreading can improve the thermal path from the die to the surrounding air. The package, the PCB, and the operating environment together determine the junction temperature that the device will actually reach.
Thermal Resistance Model
The thermal path can be represented with a simple resistance model. The key terms are:
- θ = thermal resistance, °C/W
- P = total device power dissipation, W
- T = temperature, °C
- ΔT = temperature differential = P × θ
- θJA = junction-ambient thermal resistance
- θJC = junction-case thermal resistance
- θCA = case-ambient thermal resistance
- θJA = θJC + θCA
- TJ = TA + (P × θJA)
Note: TJ(Max) = 150°C (Sometimes 175°C).
With this model, the junction temperature is calculated from the ambient temperature plus the temperature rise caused by power dissipation through the junction-to-ambient thermal resistance. The total thermal resistance is the sum of the junction-to-case path and the case-to-ambient path. This relationship allows the designer to estimate whether the AD8017AR or a similar device will remain below its maximum junction temperature under the actual PCB and environmental conditions of the application.
Thermal Design Basics
Thermal resistance is normally represented by the symbol θ. Its unit is °C/W. Unless otherwise specified, thermal resistance refers to the resistance encountered by heat flowing from the IC junction to the ambient air. It can also be expressed more specifically as θJA, the junction-to-ambient thermal resistance. θJC and θCA are two other forms of θ, described below.
In general, a device with a thermal resistance θ equal to 100°C/W will exhibit a 100°C temperature difference at 1W power dissipation, with that value measured between two reference points. Note that this is a linear relationship, so in the same device, 1W of dissipation produces a 100°C temperature difference, and so on. For the AD8017AR, θ is about 95°C/W, so 1.3W dissipation produces a junction-to-ambient temperature difference of approximately 124°C. This temperature rise is exactly what is used to predict internal temperature and to judge the thermal reliability of the design. When the ambient temperature is 25°C, an internal junction temperature of about 150°C is allowed. In practice, most ambient temperatures are above 25°C, so the power that can be handled is somewhat lower.
For any power dissipation P in W, the effective temperature difference ΔT in °C can be calculated with the following equation:
ΔT = P × θ
Here, θ is the total applicable thermal resistance. Thermal resistance is not a single fixed property of the die alone; it is defined by the thermal path and by the reference points used. The same die can therefore have a different θJA in a different package or on a different PCB layout. For first-order thermal estimates, the linear relationship above is useful because it directly links power dissipation, thermal resistance, and temperature rise.

Note that series thermal resistances, such as the two series elements shown at the right of the figure, model the total thermal resistance path a device may encounter. In calculation, the total θ is the sum of the two thermal resistances, that is, θJA = θJC + θCA. Given the ambient temperature TA, the power P, and θ, the junction temperature TJ can be calculated. According to the relationships shown, maintaining a low TJ requires keeping θ or power dissipation, or both, low. A low ΔT is key to extending semiconductor life because a low ΔT reduces the maximum junction temperature.
In an IC, one temperature reference point is always a node of the device, namely the hottest point inside the chip operating in a given package. The other relevant reference points are TC, the device case, or TA, the surrounding air. These reference points lead to the thermal resistances mentioned earlier, namely θJC and θJA.
Consider first the simplest case, in which θJA is the thermal resistance measured between the junction and the ambient air for a given device. This thermal resistance usually applies to small, relatively low-power ICs such as op amps, whose dissipation is often 1W or less. In general, for an 8-pin plastic DIP or the better SOIC package, the typical θJA for op amps and other small devices is in the 90–100°C/W range.
It should be clear that these thermal resistances depend heavily on the package, because different materials have different levels of thermal conductivity. In general, the thermal resistance of conductors is similar to electrical resistance: copper is best, followed by aluminum, steel, and so on. Therefore, copper leadframe packages have the highest performance, meaning the lowest θ. The package is not just a mechanical container; it is part of the thermal path from the die to the PCB and to the surrounding air.
Heat Dissipation
By definition, a heatsink is an additional low-thermal-resistance device attached to the IC to help dissipate heat. A heatsink has its own thermal resistance, expressed as θCA in °C/W. However, most op amps today are cumbersome to mount heatsinks on, except for older TO-99 metal can packages. Devices that are designed for heatsink mounting have a clear characteristic: their θJC is much lower than their θJA. In this case, θ consists of more than one component. Thermal resistances simply add, which makes the net calculation relatively straightforward. For example, given the relevant θJC, calculating the net θJA requires only adding the heatsink thermal resistance θCA, or case-to-ambient thermal resistance, to θJC:
θJA = θJC + θCA
The result is a θJA specific to the environment. In a real system, the case-to-ambient path may include the heatsink, the thermal interface, and the surrounding air, so the sum represents the complete thermal path from junction to ambient.
More broadly, however, modern ICs do not use commercially available heatsinks. Instead, when significant power must be dissipated, such as ≥1W, low-thermal-resistance copper PCB traces are used as the heatsink. In this case, the most useful processing data provided by the manufacturer is the boundary condition of an example PCB layout and the θJA produced under those conditions. As described earlier, this is the specific information provided for the AD8017AR. Through this approach, example data showing thermal relationships under such conditions is shown in the following figure. These data apply to an AD8017AR fitted with a heatsink area of about 4 square inches, using a double-layer 2 oz copper PCB. The board area, copper thickness, layer count, and via arrangement all form part of that thermal path, so the resulting θJA should be understood together with the stated layout conditions.

These curves present the relationship between maximum power dissipation and temperature characteristics for the AD8017 at maximum junction temperatures of 150°C and 125°C. Such curves are often called derating curves because the allowable power dissipation decreases as ambient temperature rises.
The AD8017AR uses ADI's proprietary thermally enhanced (Thermal Coastline) IC package, which allows more power to be dissipated without increasing the SO-8 package size. For a TJ(max) of 150°C, the upper curve shows the allowable dissipation of this package, which is 1.3W at an ambient temperature of 25°C. If the more conservative 125°C TJ(max) is used, the lower of the two curves applies.
The following figure compares the performance of the 8-pin standard SOIC package with the ADI thermally enhanced package. Note that the thermally enhanced package allows 1.3W at 25°C, while the standard package allows only 0.8W. In the thermally enhanced package, heat conduction is improved, which is exactly why the package θJA is lower.

Even higher power can be supported because the IC package can improve heat conduction from the die to the PCB. One example is the AD8016ADSL line driver device, which offers two package options, the BATWING and PSOP3, with 25°C power ratings of 5.5W and 3.5W; the PSOP3 version is the higher-rated option. The following figure shows the thermal curves for the AD8016 BATWING and PSOP3 packages, with TJ(max) = 125°C.

For the higher-rated AD8016ARP PSOP3 package, when it is combined with a 10 in2, 1 oz heat-spreading layer, the combination can handle up to 3W at an ambient temperature of 70°C, as shown by the upper curve. This corresponds to a θJA of 18°C/W, applicable at a maximum junction temperature of 125°C.
The PSOP3 version of the AD8016 achieves this power-handling capability because it uses a large copper pad. Internally, the IC die is placed directly on the copper pad, with the bottom surface exposed as shown in the following figure for the 20-pin PSOP3 package. The purpose is to solder this surface directly to a copper layer on the PCB, thereby enlarging the heat-dissipating area.

Both AD8016 package options have still-air and moving-air characteristics, but the thermal data given above apply without directed airflow. Therefore, adding airflow further reduces the thermal resistance.
Design Guidelines for Low Thermal Resistance
To design a reliable low-thermal-resistance op amp circuit, the following design considerations should be reviewed. Consider all points as appropriate for the actual application.
- For a PCB heatsink, use as large a copper area as practical, up to the point of diminishing returns.
- In combination with item 1, use multiple external PCB layers connected by multiple vias.
- Use heavier copper where practical, preferably 2 oz or more.
- Provide adequate natural ventilation openings in the system so heat can escape freely from hot PCB surfaces.
- Orient power-dissipating PCB layers vertically to promote airflow convection in the heatsink area.
- For precision op amp applications, consider an external power buffer stage.
- For cases that must dissipate several watts in limited space, consider forced-air cooling.
- Do not cover thermal traces with solder mask.
- Do not use excessive supply voltages on powered ICs.
In most cases, the items above are obvious. Item 9, however, needs a little explanation. Whenever an application requires only a moderate voltage swing, such as standard video at 2Vp-p, a wide supply voltage range can often be used. But, at higher supply voltages an op amp driver produces greater IC power dissipation, even when load power remains constant. The following figure shows the power dissipation of a video op amp driver at various supply voltages and low output voltage swing.

In this situation, as long as the distortion performance of the application does not degrade, the IC should be supplied with a lower voltage, such as ±5V instead of ±15V. The example data above are calculated on a DC basis; compared with sinusoidal or noise-like waveforms such as DMT signals, DC increases driver power dissipation. The general principle still applies to these AC waveforms. In other words, op amp power dissipation is high when load current is high and voltage is low.
Package Size and Thermal Trade-offs
Although the AD8016 and AD8017 thermally enhanced packages have a greater opportunity to handle high power, increasingly popular small IC packages are actually moving in the opposite direction. Undoubtedly, today's small packages do sacrifice greater thermal performance. It must be understood, however, that this is done to reduce op amp package size and ultimately to increase overall system PCB density. The trade-off is deliberate: smaller packages save board area, but they also reduce the available thermal path.
These points are reflected in the thermal ratings of the AD8057 and AD8058 series single and dual op amps. The AD8057 and AD8058 op amps are available in three different packages: SOT-23-5, 8-pin μSOIC, and standard SOIC. Figure 8 shows the comparative thermal performance for several AD8057/58 op amp package options.

As the data show, as package size shrinks, the power that can be dissipated decreases significantly. For such miniature packages, the leadframe is the only heat path, so thermal performance degrades. The θJA values for the above packages are 240°C/W, 200°C/W, and 160°C/W, respectively. Note that this is a package limitation, not a device limitation. Other ICs using the same packages have similar characteristics.
Thermal Considerations for Data Converters
At first glance, it is tempting to assume that the power dissipation of an ADC or DAC is fixed once the supply voltage is set. In practice, many data converters, especially CMOS types, draw power that depends strongly on the output data load and on the sampling clock frequency. Some new high-speed converters can consume as much as 1.5W to 2W under worst-case operating conditions. This behavior must be understood clearly so that the package can be mounted in a way that keeps the junction temperature within acceptable limits at the highest expected operating temperature.
Guideline MT-031 on grounding emphasizes that the digital outputs of high-performance ADCs, particularly those with parallel outputs, should not be heavily loaded. A load of roughly 5-10pF is appropriate; heavier loading allows digital transient currents to degrade SNR and SFDR. Even with small output loads, however, the power dissipation of most CMOS and BiCMOS ADCs remains a function of the sampling clock frequency. In some cases, it also depends on the analog input frequency and amplitude.
For example, The following figure shows the relationship between power dissipation and frequency for the AD9245, a 14-bit, 80MSPS, 3V CMOS ADC, with a 2.5MHz analog input on the data lines and a 5pF output load. The curves present digital supply current, analog supply current, and total power. The total power can vary from 310mW to 380mW as the sampling frequency changes between 10MSPS and 80MSPS. This variation is large enough that a single nominal power figure is not sufficient for a thermal calculation. The worst-case sampling condition must be used, because the thermal design has to cover the highest power that the converter can dissipate in the application.

The AD9245 is supplied in a 32-pin leadless chip-scale package (LFCSP). The bottom view of the package reveals an exposed pad. This pad should be soldered to the PC board ground plane to obtain the best heat conduction. The worst-case package junction-to-ambient thermal resistance θJA is rated at 32.5°C/W. At a power dissipation of 380mW, the junction temperature is 32.5°C/W × 0.38 = 12.3°C above ambient. At a maximum operating temperature of +85°C, the junction temperature is 85°C + 12.3°C = 97.3°C. The exposed pad therefore provides a direct thermal path from the die to the ground plane, and the board copper becomes part of the thermal solution.

The AD9430 is a high-performance 12-bit, 170/210MSPS 3.3V BiCMOS ADC. It offers two output modes: a dual-channel 105MSPS demultiplexed CMOS output and a 210MSPS LVDS output. Power dissipation is a function of sampling frequency. The figure presents analog and digital supply currents in both CMOS and LVDS modes with an analog input frequency of 10.3MHz. In LVDS mode at a sampling frequency of 210MSPS, the total supply current is about 455mA, which gives a total power dissipation of 1.5W. More precisely, the total current is 55mA + 400mA = 455mA, and the total power is 3.3V × 455mA = 1.5W. The output mode and clock rate therefore have a direct effect on the thermal design, and the LVDS condition at 210MSPS is the highest power case in this example.

The AD9430 uses a 100-pin thin plastic quad flat package with an exposed pad (TQFP/EP). The conductive pad is connected to the chip ground and should be soldered to the PC board ground plane. When the package is soldered to the ground plane, its θJA in still air is 25°C/W. At 1.5W power dissipation, the junction temperature is 25°C/W × 1.5 = 37.5°C above ambient. At a maximum operating temperature of +85°C, the junction temperature is 85°C + 37.5°C = 122.5°C. This example shows how a relatively small thermal resistance still produces a significant temperature rise when the converter dissipates 1.5W.
The AD6645 is a high-performance 14-bit, 80/105MSPS ADC fabricated on a high-speed complementary bipolar process (XFCB). It provides high SFDR (89dBc) and SNR (75dB). Although its power dissipation, which is a function of sampling frequency, does not vary greatly, the maximum power dissipation of the device is 1.75W. It is housed in a thermally enhanced 52-pin PowerQuad 4- package with an exposed pad.

Soldering the exposed central heat sink to the PC board ground plane reduces the package θJA in still air to 23°C/W. For a power dissipation of 1.75W, the junction temperature is 23°C/W × 1.75 = 40.3°C above ambient. At a maximum operating temperature of +85°C, the junction temperature is 85°C + 40.3°C = 125.3°C. With 200LFPM airflow, the package thermal resistance can be reduced to 17°C/W, which brings the junction temperature to 30°C above ambient. In other words, for a +85°C operating ambient, the junction temperature is 115°C. Airflow therefore provides additional margin when the package is already close to its thermal limit.
High-speed CMOS DACs, such as the TxDAC? family, and DDS ICs, such as the AD985x series, also have power dissipation that depends on the clock rate. For the AD9777 16-bit, 160MSPS dual interpolating DAC, for example, power is a function of three factors: clock rate, output frequency, and whether the PLL and modulation functions are enabled. With a 3.3V supply, its power dissipation ranges from 380mW (fDAC=100MSPS, fOUT=1MHz, no interpolation, no modulation) to 1.75W (fDAC=400MSPS, fDATA=50MHz, fs/2 modulation, PLL enabled). Devices in this family and similar devices are offered in thermally enhanced packages with an exposed pad that must be soldered to the PC board ground plane. The same thermal calculation method applies: determine the worst-case power, obtain θJA for the mounted package, and add the resulting rise to the maximum ambient temperature.
Summary
This article has discussed thermal application issues for operational amplifiers and data converters, but it has not covered the classic clip-on or bolt-on heatsink technique. It has also not covered forced-air cooling, which is generally used when tens of watts of power must be handled. The main reason for omitting these topics is that they do not apply to today's operational amplifier and data converter packages.
Related Reading:
Eight Layout Considerations for Differential Filters on PCBs
Improving PCB Immunity to Power Supply Variations in Converter Systems
PCB Layout for Accurate Temperature Measurement: PCB vs Ambient
Best Grounding Practices for Data Converters: Return Paths and Error Voltage
High-Temperature IC Packaging: Die Attach, Wire Bond, Solder and PCB
isoPower Radiated Emissions: Dense PCB Layout Guide
Buck Regulator PCB Layout and Grounding Guide for Low Noise
LFCSP Package Rework: Safe Removal and Replacement on PCBs
PBGA Rework Procedure: Removal, Pad Cleaning, Paste and Placement